• Boot the switch into SWITCH ROM mode. • Initialize the flash file system. • OPTIONAL – Format the flash file system if needed. (This will remove your startup configuration) • Set the baud rate to 115200 to increase xmodem transfer speed and decrease time required to restore the IOS Image. Running Cisco Switches on GNS3. Here some awesome articles on how to run Cisco Switch(CLI) on GNS3. Password: cisco. Now open the browser and upload the necessary files. These files are available on “L2 & L3 IOU IOS. - Another Century's Episode 2 (Special Vocal Version) [NTSC-J] [SLPS-25829] A.C.E. (Complete Edition) [NTSC-J] [SLPM-66089] 3LDK - Shiawase ni Narouyo (Limited Edition) [NTSC-J] [SLPM-65607] A-Ressha de Ikou 2001 [NTSC-J] [SLPS-25017] A.C.E. Beatmania iidx 14 gold ps2 iso. • Copy the Cisco IOS Image via xModem to Flash: • Set the boot parameter to the new image name located in Flash: • Unset the baud so that it defaults back to 9600. • Boot the switch and verify that the switch boots properly. Lab Instruction Recovering the Cisco IOS Image on a fix configuration Cisco Catalyst Series Switch is quite a bit different and more of an “old school” way of doing an IOS image recovery. Unfortunately fixed configuration switches require the use of xModem to restore a corrupt or missing IOS images unlike the Cisco 4500 and Cisco 6500 Series supervisor engines which use compact flash cards Step 1. Boot your switch into switch ROM mode. This typically involves holding down the STAT button on the front of the switch when plugging in the power. You can check out the required procedure by clicking Once you’ve booted your switch into Switch ROM mode you’ll be see the following dispatch; Boot Sector Filesystem (bs) installed, fsid: 2 Base ethernet MAC Address: 00:14:f2:d2:41:80 Xmodem file system is available. The password-recovery mechanism is enabled. The system has been interrupted prior to initializing the flash filesystem. • Install the Software Pack by: • Double-clicking on the.pack file on your USB-Stick and confirming the destination path, or • Open MDK-5, select the Pack Installer and use File/Import. Keil c 4 keygen software. • Start the MDK-5 installation as explained at: or:. MORE INFORMATION Please refer to our MDK-5 introduction at: • • Refer to in the µVision User's Guide. • Install the Legacy Pack by double-clicking on the MDKCM*.exe- or MDK79*.exe-file on your USB-Stick. • Plug the USB-Stick into the target PC which is not connected to the Internet. The following commands will initialize the flash filesystem, and finish loading the operating system software: flash_init boot switch: Step 2. Once you’ve booted into Switch ROM mode you’ll need to initialize the flash file system by executing the flash_init command as shown below; switch: flash_init Initializing Flash. Flashfs[0]: 1 files, 1 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 15998976 flashfs[0]: Bytes used: 12474880 flashfs[0]: Bytes available: 3524096 flashfs[0]: flashfs fsck took 10 seconds.done Initializing Flash. Switch: Step 3 – OPTIONAL – If your image is corrupted you can format your flash file system by executing the format flash: command as shown below however this will delete your start-up configuration!!! Switch: format flash: Are you sure you want to format 'flash:' (all data will be lost) (y/n)?y flashfs[0]: 0 files, 1 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 7741440 flashfs[0]: Bytes used: 1024 flashfs[0]: Bytes available: 7740416 flashfs[0]: flashfs fsck took 12 seconds. Filesystem 'flash:' formatted Switch: Step 4. To speed up the xModem file transfer speed you’ll need to set the console line BAUD rate to 115200 by executing the set BAUD 115200. If you do this you’ll need to disconnect your console session and change the serial line speed from 9600 to 115200. However if you do not set the BAUD to 115200 your file transfer can take up to 3 hours. Switch: set BAUD 115200 每 Step 5. Once setting the BAUD rate and reconnecting to the console line of your Cisco switch you’re ready to copy the IOS image via xModem to the switch’s flash memory by executing the copy xmodem: flash:filename.bin and starting the xModem file transfer from the terminal emulator client as shown below; switch: copy xmodem: flash:c3560-ipservicesk9-mz.122-53.SE.bin Begin the Xmodem or Xmodem-1K transfer now. CCC Starting xmodem transfer. Press Ctrl+C to cancel.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |